 |
Advanced Settings |
7.Hardware Setup
Tuner
AM/FM Frequency Step (North American and Taiwanese models)
Default Value : 10kHz/200kHz
Select a frequency step depending on your area of residence.
Select "10kHz/200kHz" or "9kHz/50kHz".
When this setting is changed, all radio presets are deleted.
AM Frequency Step (European, Australian and Asian models)
Default Value : 9kHz
Select a frequency step depending on your area of residence.
Select "10kHz" or "9kHz".
When this setting is changed, all radio presets are deleted.
HDMI
HDMI CEC (RIHD)
Default Value : Off
Setting to "On" enables the input selection link and other link functions with HDMI connected CEC compliant device.
"On": Use this function
"Off": Do not use this function
Depending on the TV set, a link may need to be configured on the TV.
This function is effective only when the device is connected to the HDMI OUT MAIN terminal.
Setting to "On" and closing the on-screen menu displays the name of the CEC-compatible components and "RIHD On" on the display.
Power consumption in standby mode may increase if "On" is set. (Depending on the TV status, the unit will enter the normal standby mode.)
If you operate the MASTER VOLUME control of the unit when this setting is set to "On" and you are listening to the audio through the speakers of your TV, audio will be output also from the speakers connected to the unit. If you want to output from only either of them, change the unit or TV settings, or reduce the volume of the unit.
If abnormal operation occurs when you set the setting to "On", set it to "Off".
When connecting a non-CEC compatible component, or when you are not sure whether it is compatible, set the setting to "Off".
When changing this setting, turn off and then on again the power of all connected components.
HDMI Through
Default Value : Off
You can display the video of an HDMI connected player on the TV even if the unit is in standby mode. This setting is effective only for an input selector to which an HDMI jack is assigned in "HDMI Input". It cannot be set to any other input selector unless an HDMI jack is assigned to it.
"Off": The setting is disabled. Video of device connected to any jack will not be displayed.
"BD/DVD", "CBL/SAT", "STB/DVR", "GAME", "PC", "AUX", "TV/CD", "PHONO": Video of the device connected to the HDMI IN jack assigned to each input will be displayed on the TV.
"Last": Video of the device connected to the HDMI IN jack assigned to the input selector that was selected immediately before the unit enters standby mode will be displayed on the TV.
"Auto": Video of all the devices connected to the HDMI IN jacks will be output to the TV.
"Eco": Video of all the devices connected to the HDMI IN jacks will be output to the TV. If you select this setting when using a CEC-compatible TV, you can reduce the power consumption in standby mode. It cannot be selected if "HDMI CEC (RIHD)" is set to "Off".
When "HDMI Through" is enabled, the power consumption increases even when the unit is on standby. However, the increase in power consumption is kept to a minimum by automatically entering the HYBRID STANDBY mode, where only the essential circuit is operating.
When changing the setting, turn off and then on again the power of all connected components.
Audio TV Out (MAIN)
Default Value : Off
You can enjoy audio through the speakers of the HDMI connected TV while this unit is on.
"On": Use this function
"Off": Do not use this function
If you select "On", set "HDMI CEC (RIHD)" to "Off."
The setting is fixed to "Auto" if "HDMI CEC (RIHD)" is set to "On".
Listening mode cannot be changed if "Audio TV Out (MAIN)" is set to "On" and audio is being output through the speakers of the TV.
Depending on your TV set or input signal of the component, audio may not output through the speakers of the TV even if this setting is set to "On". In such case, audio is output from the speakers of the unit.
If you operate the MASTER VOLUME control of the unit when "Audio TV Out (MAIN)" or "HDMI CEC (RIHD)" is set to "On" and you are listening to the audio through the speakers of your TV, audio will be output from the unit. If you do not want to output audio from the unit, change the unit or TV settings, or reduce the volume of the unit.
"Audio TV Out (MAIN)" is fixed to "Off" if "Monitor Out" is set to "SUB".
Audio TV Out (SUB)
Default Value : Off
You can enjoy audio through the speakers of the HDMI connected TV while this unit is on.
"On": Use this function
"Off": Do not use this function
Listening mode cannot be changed while "Audio TV Out (SUB)" is set to "On" and audio is being output through the speakers of the TV.
Depending on your TV set or input signal of the component, audio may not output through the speakers of the TV even if this setting is set to "On". In such case, audio is output from the speakers of the unit.
If you operate the MASTER VOLUME control of the unit when "Audio TV Out (SUB)" or "HDMI CEC (RIHD)" is set to "On" and you are listening to the audio through the speakers of your TV, audio will be output from the unit.. If you do not want to output audio from the unit, change the unit or TV settings, or reduce the volume of the unit.
"Audio TV Out (SUB)" is fixed to "Off" if "Monitor Out" is set to "MAIN".
Audio Return Channel
Default Value : -
You can enjoy sound of the HDMI connected ARC compatible TV through the speakers connected to the unit. To use this function, set "HDMI CEC (RIHD)" to "On" in advance.
"Auto": When enjoying the TV sound through the speakers connected to the unit
"Off": When not using the ARC function
Lip Sync
Default Value : On
This setting automatically corrects any desynchronization between the video and audio signals based on data from the HDMI LipSync compatible TV.
"On": Automatic correction will be enabled.
"Off": Automatic correction will be disabled.
InstaPrevue
Change the preview display of the video input through HDMI, which will be displayed using "InstaPrevue" in the Home menu.
Depending on the video source, the preview thumbnails configured in "InstaPrevue" may not be displayed properly.
Sub Window
Default Value : Multi
Set how to display preview thumbnails.
"Multi": Displays all the thumbnails of HDMI IN1, 2, 3, 4 and FRONT at once.
"Single": Displays each thumbnail individually.
Position
Default Value : Bottom/Lower Right
Set the position to display preview thumbnails.
When "Multi" is selected for "Sub Window": Select from "Top", "Bottom", "Left" and "Right".
When "Single" is selected for "Sub Window": Select from "Upper Left", "Upper Right", "Lower Left" and "Lower Right".
If "Monitor Out" is set to "MAIN+SUB" and "Audio TV Out (SUB)" is set to "On"
–Set the audio output of the connected device to "2ch PCM".
–If the audio input is via other than HDMI, sound of the TV connected to the HDMI OUT SUB jack will not be output.
Auto Standby
Auto Standby
Default Value : On/Off
This setting places the unit on standby automatically after 20 minutes of inactivity without any video or audio input.
"On": The unit will automatically enter standby mode ("ASb" will light).
"Off": The unit will not automatically enter standby mode.
"Auto Standby" is appeared on the display and menu screen 30 seconds before the Auto Standby comes on.
"Auto Standby" does not work when Zone 2 is active.
Default values vary depending on the regions.
HDMI Through
Default Value : Off
Enable or disable "Auto Standby" while "HDMI Through" is on.
"On": The setting will be enabled.
"Off": The setting will be disabled.
"HDMI Through" cannot be set to "On" if "Auto Standby" is set to "Off".
When "HDMI Through" is used, the power consumption increases even when the unit is on standby. However, the increase in power consumption is kept to a minimum by automatically entering the HYBRID STANDBY mode, where only the essential circuit is operating.
Network
Make the network setting.
When LAN is configured with a DHCP, set "DHCP" to "Enable" to configure the setting automatically. ("Enable" is set by default) To assign fixed IP addresses to each components, you must set "DHCP" to "Disable" and assign an address to this unit in "IP Address" as well as set information related to your LAN, such as Subnet Mask and Gateway.
Network Standby
Default Value : Off
You can turn on the power of the unit via network using an application such as Onkyo Remote.
"On": Use this function
"Off": Do not use this function
When "Network Standby" is used, the power consumption increases even when the unit is on standby. However, the increase in power consumption is kept to a minimum by automatically entering the HYBRID STANDBY mode, where only the essential circuit is operating.
Wi-Fi
Default Value : Off (Wired)
Connect the unit to network via wireless LAN router.
"On": Wireless LAN connection
"Off (Wired)": Wired LAN connection
Wi-Fi Setup
Default Value : –
You can configure wireless LAN settings by pressing ENTER when "Start" is displayed.
Wi-Fi Status
Default Value : –
The information of the connected access point will be displayed.
"SSID": SSID of the connected access point.
"Security": Security method of the connected access point.
"Signal": Signal strength of the connected access point.
"Status": Status of the connected access point.
MAC Address
Default Value : –
This is the MAC address of the AV receiver.
This value is specific to the component and cannot be changed.
DHCP
Default Value : Enable
"Enable": Auto configuration by DHCP
"Disable": Manual configuration without DHCP
If selecting "Disable", you must set "IP Address", "Subnet Mask", "Gateway", and "DNS Server" manually.
IP Address
Default Value : –
Displays/Sets the IP address.
Subnet Mask
Default Value : –
Displays/Sets the subnet mask.
Gateway
Default Value : –
Displays/Sets the gateway.
DNS Server
Default Value : –
Displays/Sets the primary DNS server.
Proxy URL
Default Value : –
Displays/Sets the proxy server URL.
Proxy Port
Default Value : –
Displays/Sets the proxy server port number when you enter "Proxy URL".
Network Check
Default Value : –
You can check the network connection.
Press ENTER when "Start" is displayed.
Wait for a while if "Network" is not shown on the screen. It will appear when the network function is started up.
Bluetooth
Bluetooth
Default Value : On
Select whether or not to use the Bluetooth function.
"On": Enables connection with a Bluetooth-enabled device by using the Bluetooth function. Select "On" also when making various Bluetooth settings.
"Off": When not using the Bluetooth function
Direct Change
Default Value : On
The input of the unit will automatically be switched to "BLUETOOTH" when connection is made from a Bluetooth-enabled device to the unit.
"On": The input will automatically become "BLUETOOTH" when a Bluetooth-enabled device is connected.
"Off": The function is disabled.
If the input is not switched automatically, set to "Off" and change the input manually.
Auto Reconnect
Default Value : On
This function automatically reconnects to the Bluetooth-enabled device connected last when you change the input selector to "BLUETOOTH".
"On": Use this function
"Off": Do not use this function
This function may not work depending on your Bluetooth-enabled device.
Wakeup via Bluetooth
Default Value : Off
This function wakes up the unit on standby by connecting a Bluetooth-enabled device.
"On": Use this function
"Off": Do not use this function
Setting to "On" increases the power consumption even when the unit is on standby. However, the increase in power consumption is kept to a minimum by automatically entering the HYBRID STANDBY mode, where only the essential circuit is operating.
"Wakeup via Bluetooth" is fixed to "Off" if "Direct Change" is set to "Off".
Pairing Information
Default Value : -
When paring is performed, the information of the previous pairing stored in this unit will be initialized.
Pressing ENTER when "Clear" is displayed initializes the pairing information stored in this unit.
This function does not initialize the pairing information on the Bluetooth-enabled device. When pairing the unit again with the device, be sure to clear the pairing information on the Bluetooth-enabled device in advance. For information on how to clear the pairing information, refer to the Bluetooth-enabled device's instruction manual.
Device
Default Value : –
Displays the name of the Bluetooth-enabled device connected to the unit.
The name is not displayed when "Status" is "Ready" and "Pairing".
Status
Default Value : –
Displays the status of the Bluetooth-enabled device connected to the unit.
"Ready": Not paired
"Pairing": Paired
"Connected": Successfully connected
Firmware Update
Update Notice
Default Value : Enable
Availability of a firmware update will be notified via network.
"Enable": Notify updates
"Disable": Do not notify updates
Version
Default Value : –
The current firmware version will be displayed.
Update via NET
Default Value : –
Press ENTER to select when you want to update the firmware via network.
You will not be able to select this setting if you do not have Internet access or there is nothing to update.
Update via USB
Default Value : –
Press ENTER to select when you want to update the firmware via USB.
You will not be able to select this setting if a USB storage device is not connected or there is nothing to update in the USB storage device.
Initial Setup
You can make the initial setup from the setup menu.
Setting is not possible if "Monitor Out" is set to "SUB".
(C) Copyright 2014 Onkyo Corporation Japan. All rights reserved.
