 |
Advanced Settings |
2.Speaker Setup
Allows you to change the speaker configuration such as existence of subwoofer, crossover frequency, and so on. Settings are automatically configured if you use the Automatic Speaker Setup.
Furthermore, you will not be able to select this setting if you have a pair of headphones connected or you are listening through your TV speakers.
Speaker Settings
Change the impedance of the connected speakers, the type of front speaker connection, and other speaker settings.
Speaker Impedance (European, Australian and Asian models)
Default Value : 6ohms
Set the impedance of the connected speakers.
"4ohms": When any of the connected speakers have 4 Ω or more to less than 6 Ω impedance
"6ohms": When the connected speakers all have 6 Ω or more impedance
Front Speakers Type
Default Value : Normal
Select the type of front speaker connection.
"Normal": When front speakers are connected in a normal manner
"Bi-Amp": When front speakers are bi-amp connected
Powered Zone 2
Default Value : No
Set presence of speaker terminal connection of Zone 2
"Yes": When speakers are connected to ZONE2 speaker terminals
"No": When speakers are not connected to ZONE2 speaker terminals
If "Front Speakers Type" is set to "Bi-Amp", this setting will be set to "No".
For impedance, check the indications on the back of the speakers or their instruction manual.
Speaker Configuration
Allows you to change the speaker configuration such as presence or not of each speaker, crossover frequency, and so on. Settings are automatically configured if you use the Automatic Speaker Setup. Audio will not be output while you are making this setting.
Subwoofer
Default Value : Yes
Set whether a subwoofer is connected or not.
"Yes": When subwoofer is connected
"No": When subwoofer is not connected
Front
Default Value : 100Hz
Select the frequency to start outputting bass frequencies (crossover frequency) for each channel from "40Hz" to "200Hz".
"Full Band": Full band will be output.
"None": When no compatible speaker is connected
"Front" will be fixed to "Full Band" if "Subwoofer" is set to "No", and the bass frequencies of the other channels will be output from the front speakers. To make the settings, refer to the instruction manual of the speakers used.
Center
Default Value : 100Hz
Select the frequency to start outputting bass frequencies (crossover frequency) for each channel from "40Hz" to "200Hz".
"Full Band": Full band will be output.
"None": When no compatible speaker is connected
This setting cannot be set to "Full Band" unless "Front" is set to "Full Band".
Surround
Default Value : 100Hz
Select the frequency to start outputting bass frequencies (crossover frequency) for each channel from "40Hz" to "200Hz".
"Full Band": Full band will be output.
"None": When no compatible speaker is connected
This setting cannot be set to "Full Band" unless "Front" is set to "Full Band".
Back
Default Value : 100Hz
Select the frequency to start outputting bass frequencies (crossover frequency) for each channel from "40Hz" to "200Hz".
"Full Band": Full band will be output.
"None": When no compatible speaker is connected
In the following cases, this setting will be set to "None":
–"Surround" is set to "None".
–"Front Speakers Type" is set to "Bi-Amp".
–"Powered Zone 2" is set to "Yes" and also Zone2 is set to on.
This setting cannot be set to "Full Band" unless "Surround" is set to "Full Band".
Height
Default Value : None
Select the frequency to start outputting bass frequencies (crossover frequency) for each channel from "40Hz" to "200Hz".
"Full Band": Full band will be output.
"None": When no compatible speaker is connected
In the following cases, this setting will be set to "None":
–"Surround" is set to "None".
–"Front Speakers Type" is set to "Bi-Amp".
–"Powered Zone 2" is set to "Yes" and also Zone2 is set to on.
This setting cannot be set to "Full Band" unless "Front" is set to "Full Band".
Back ch
Default Value : 2ch
Select the number of channels of the connected surround back speaker.
"1ch": When one speaker is connected (Connect to the BACK or HEIGHT L terminal)
"2ch": When two speakers are connected
The setting cannot be changed if "Surround" or "Back" is set to "None".
LPF of LFE
Default Value : 120Hz
Set the low-pass filter for LFE (low-frequency effect) signals in order to pass lower frequency signals than the set value and thus cancel unwanted noises. The low-pass filter will be effective only on sources with LFE channel.
Set a frequency from "80Hz", "90Hz", "100Hz" and "120Hz".
"Off": Do not use this function
Double Bass
Default Value : -----
Boost bass output by feeding bass sounds from the front left and right, and center speakers to the subwoofer.
"On": Bass output will be boosted.
"Off": Bass output will not be boosted.
The setting will not automatically be configured even if you performed the automatic speaker setup.
If "Subwoofer" is set to "No" or if "Front" is set to other than "Full Band", the setting will be fixed to "-----".
Speaker Distance
Set the distance from each speaker to the listening position. Settings are automatically configured if you use the automatic speaker setup.
Unit
Default Value : feet/meters
Specify the unit of distance for configuring settings.
"feet": When setting in feet (0.1 ft to 30.0 ft, in increments of 0.1 ft)
"meters": When setting in meters (0.03 m to 9.00 m, in increments of 0.03 m)
Front Left
Default Value : 12.0 ft/3.60 m
Specify the distance between each speaker and the listening position.
Center
Default Value : 12.0 ft/3.60 m
Specify the distance between each speaker and the listening position.
Front Right
Default Value : 12.0 ft/3.60 m
Specify the distance between each speaker and the listening position.
Surround Right
Default Value : 7.0 ft/2.10 m
Specify the distance between each speaker and the listening position.
Back Right
Default Value : 7.0 ft/2.10 m
Specify the distance between each speaker and the listening position.
This setting cannot be changed when "Powered Zone 2" is set to "Yes" and Zone 2 is turned on.
Back Left
Default Value : 7.0 ft/2.10 m
Specify the distance between each speaker and the listening position.
This setting cannot be changed when "Powered Zone 2" is set to "Yes" and Zone 2 is turned on.
Surround Left
Default Value : 7.0 ft/2.10 m
Specify the distance between each speaker and the listening position.
Subwoofer
Default Value : 12.0 ft/3.60 m
Specify the distance between each speaker and the listening position.
Height Left
Default Value : 9.0 ft/2.70 m
Specify the distance between each speaker and the listening position.
This setting cannot be changed when "Powered Zone 2" is set to "Yes" and Zone 2 is turned on.
Height Right
Default Value : 9.0 ft/2.70 m
Specify the distance between each speaker and the listening position.
This setting cannot be changed when "Powered Zone 2" is set to "Yes" and Zone 2 is turned on.
When the speaker is set to "No" or "None" in "Speaker Configuration", the settings for "Speaker Distance" cannot be changed:
Default values vary depending on the regions.
Level Calibration
Adjust the level of each speaker with the built-in test tone. Settings are automatically configured if you use the Automatic Speaker Setup.
Front Left
Default Value : 0 dB
Select a value between "-12 dB" to "+12 dB". A test tone will be output each time you change the value. Select the desired level.
Center
Default Value : 0 dB
Select a value between "-12 dB" to "+12 dB". A test tone will be output each time you change the value. Select the desired level.
Front Right
Default Value : 0 dB
Select a value between "-12 dB" to "+12 dB". A test tone will be output each time you change the value. Select the desired level.
Surround Right
Default Value : 0 dB
Select a value between "-12 dB" to "+12 dB". A test tone will be output each time you change the value. Select the desired level.
Back Right
Default Value : 0 dB
Select a value between "-12 dB" to "+12 dB". A test tone will be output each time you change the value. Select the desired level.
Back Left
Default Value : 0 dB
Select a value between "-12 dB" to "+12 dB". A test tone will be output each time you change the value. Select the desired level.
Surround Left
Default Value : 0 dB
Select a value between "-12 dB" to "+12 dB". A test tone will be output each time you change the value. Select the desired level.
Subwoofer
Default Value : 0 dB
Select a value between "-15 dB" to "+12 dB". A test tone will be output each time you change the value. Select the desired level.
Height Left
Default Value : 0 dB
Select a value between "-12 dB" to "+12 dB". A test tone will be output each time you change the value. Select the desired level.
Height Right
Default Value : 0 dB
Select a value between "-12 dB" to "+12 dB". A test tone will be output each time you change the value. Select the desired level.
In the following cases, the settings for "Level Calibration" cannot be changed:
–The speaker is set to "No" or "None" in "Speaker Configuration".
–Mute (MUTING) is set.
(C) Copyright 2014 Onkyo Corporation Japan. All rights reserved.
