 |
Advanced Settings (Setup Menu) |
2. Speaker
Allows you to change the speaker configuration such as presence or not of subwoofer, crossover frequency, and so on. Settings are automatically configured if you use the Automatic Speaker Setup.
This setting cannot be selected if headphones are connected or audio is output from the speakers of the TV.
Configuration
You can change the number of speaker channels connected, the type of front speaker connection, the height speaker type, and other speaker settings.
Speaker Channels
Default Value: 7.1 ch
Select "2.1 ch", "3.1 ch", "4.1 ch", "5.1 ch", "6.1 ch", "7.1 ch", "2.1.2 ch", "3.1.2 ch", "4.1.2 ch", or "5.1.2 ch" to suit the number of speaker channels connected.
Subwoofer
Default Value: Yes
Set whether a subwoofer is connected or not.
"Yes": When subwoofer is connected
"No": When subwoofer is not connected
Height Speaker
Default Value: Front High
Set the speaker type if height speakers are connected to the BACK or HEIGHT terminals.
Select "Front High", "Top Front", "Top Middle", "Top Rear", "Rear High", "Dolby Speaker (Front)", or "Dolby Speaker (Surr)" according to the connected speaker type and location.
If an item cannot be selected even though connection is correct, check that the settings in "Speaker Channels" matches the number of connected channels.
Bi-Amp
Default Value: No
Set whether your front speaker connection is bi-amp.
"No": When front speakers are connected in a normal manner
"Yes": When front speakers are bi-amp connected
If an item cannot be selected even though connection is correct, check that the settings in "Speaker Channels" matches the number of connected channels.
Powered Zone 2
Default Value: No
Set the connection of speakers to Zone 2 speaker terminals.
"Yes": When speakers are connected to ZONE2 speaker terminals
"No": When speakers are not connected to ZONE2 speaker terminals
This item will be set to "No" when "Bi-Amp" is set to "Yes".
Crossover
Allows you to change speaker configurations, such as crossover frequency. Settings are automatically configured if you use the Automatic Speaker Setup. Audio will not be output while you are making this setting.
Front
Default Value: 100 Hz
Select the crossover frequency from "40Hz" to "200Hz" to start outputting frequencies for each channel.
"Full Band": Full band will be output.
If "Configuration" - "Subwoofer" is set to "No", "Front" will be fixed to "Full Band" and the low pitched range of the other channels will be output from the front speakers. Refer to the instruction manual of your speakers to make the setting.
Center
Default Value: 100 Hz
Select the crossover frequency from "40Hz" to "200Hz" to start outputting frequencies for each channel.
"Full Band": Full band will be output.
"Full Band" can be selected only when "Front" is set to "Full Band".
If an item cannot be selected even though connection is correct, check that the settings in "Configuration" - "Speaker Channels" matches the number of connected channels.
Height
Default Value: 100 Hz
Select the crossover frequency from "40Hz" to "200Hz" to start outputting frequencies for each channel.
"Full Band": Full band will be output.
"Full Band" can be selected only when "Front" is set to "Full Band".
If an item cannot be selected even though connection is correct, check that the settings in "Configuration" - "Speaker Channels" matches the number of connected channels.
Surround
Default Value: 100 Hz
Select the crossover frequency from "40Hz" to "200Hz" to start outputting frequencies for each channel.
"Full Band": Full band will be output.
"Full Band" can be selected only when "Front" is set to "Full Band".
If an item cannot be selected even though connection is correct, check that the settings in "Configuration" - "Speaker Channels" matches the number of connected channels.
Back
Default Value: 100 Hz
Select the crossover frequency from "40Hz" to "200Hz" to start outputting frequencies for each channel.
"Full Band": Full band will be output.
This cannot be selected in the following conditions.
–The setting for "Configuration" - "Bi-Amp" is "Yes"
–"Configuration" - "Powered Zone 2" is set to "Yes" and ZONE 2 is on
"Full Band" can be selected only when "Surround" is set to "Full Band".
If an item cannot be selected even though connection is correct, check that the settings in "Configuration" - "Speaker Channels" matches the number of connected channels.
LPF of LFE
Default Value: 120Hz
Set the low-pass filter for LFE (low-frequency effect) signals in order to pass lower frequency signals than the set value and thus cancel unwanted noises. The low-pass filter will be effective only on sources with LFE channel.
The value from "80Hz" to "120Hz" can be set.
"Off": Do not use this function
Double Bass
Default Value: On
This can only be selected when "Configuration" - "Subwoofer" is set to "Yes" and "Front" is set to "Full Band".
Boost bass output by feeding bass sounds from the front left and right, and center speakers to the subwoofer.
"On": Bass output will be boosted.
"Off": Bass output will not be boosted.
The setting will not automatically be configured even if you performed the automatic speaker setup.
Distance
Set the distance from each speaker to the listening position. Settings are automatically configured if you use the automatic speaker setup.
Unit
Default Value: feet/meters
Specify the unit of distance for configuring settings.
"feet": When setting in feet (0.1 ft to 30.0 ft, in increments of 0.1 ft)
"meters": When setting in meters (0.03 m to 9.00 m, in increments of 0.03 m)
Front Left
Default Value: 12.0ft/3.60m
Specify the distance between each speaker and the listening position.
Center
Default Value: 12.0ft/3.60m
Specify the distance between each speaker and the listening position.
Front Right
Default Value: 12.0ft/3.60m
Specify the distance between each speaker and the listening position.
Height Left
Default Value: 9.0ft/2.70m
Specify the distance between each speaker and the listening position.
This setting cannot be changed if "Configuration" - "Powered Zone 2" is set to "Yes" and Zone2 is set to on.
Height Right
Default Value: 9.0ft/2.70m
Specify the distance between each speaker and the listening position.
This setting cannot be changed if "Configuration" - "Powered Zone 2" is set to "Yes" and Zone2 is set to on.
Surround Right
Default Value: 7.0ft/2.10m
Specify the distance between each speaker and the listening position.
Back Right
Default Value: 7.0ft/2.10m
Specify the distance between each speaker and the listening position.
This setting cannot be changed if "Configuration" - "Powered Zone 2" is set to "Yes" and Zone2 is set to on.
Back Left
Default Value: 7.0ft/2.10m
Specify the distance between each speaker and the listening position.
This setting cannot be changed if "Configuration" - "Powered Zone 2" is set to "Yes" and Zone2 is set to on.
Surround Left
Default Value: 7.0ft/2.10m
Specify the distance between each speaker and the listening position.
Subwoofer
Default Value: 12.0ft/3.60m
Specify the distance between each speaker and the listening position.
Default values vary depending on the regions.
The speaker "Distance" may be unable to be changed depending on the settings in "Configuration" - "Speaker Channels" / "Subwoofer".
Level Calibration
Adjust the level of each speaker with the built-in test tone. Settings are automatically configured if you use the Automatic Speaker Setup.
Front Left
Default Value: 0 dB
Select a value between "-12 dB" and "+12 dB". A test tone will be output each time you change the value. Select the desired level.
Center
Default Value: 0 dB
Select a value between "-12 dB" and "+12 dB". A test tone will be output each time you change the value. Select the desired level.
Front Right
Default Value: 0 dB
Select a value between "-12 dB" and "+12 dB". A test tone will be output each time you change the value. Select the desired level.
Height Left
Default Value: 0 dB
Select a value between "-12 dB" and "+12 dB". A test tone will be output each time you change the value. Select the desired level.
This setting cannot be changed if "Configuration" - "Powered Zone 2" is set to "Yes" and Zone2 is set to on.
Height Right
Default Value: 0 dB
Select a value between "-12 dB" and "+12 dB". A test tone will be output each time you change the value. Select the desired level.
This setting cannot be changed if "Configuration" - "Powered Zone 2" is set to "Yes" and Zone2 is set to on.
Surround Right
Default Value: 0 dB
Select a value between "-12 dB" and "+12 dB". A test tone will be output each time you change the value. Select the desired level.
Back Right
Default Value: 0 dB
Select a value between "-12 dB" and "+12 dB". A test tone will be output each time you change the value. Select the desired level.
This setting cannot be changed if "Configuration" - "Powered Zone 2" is set to "Yes" and Zone2 is set to on.
Back Left
Default Value: 0 dB
Select a value between "-12 dB" and "+12 dB". A test tone will be output each time you change the value. Select the desired level.
This setting cannot be changed if "Configuration" - "Powered Zone 2" is set to "Yes" and Zone2 is set to on.
Surround Left
Default Value: 0 dB
Select a value between "-12 dB" and "+12 dB". A test tone will be output each time you change the value. Select the desired level.
Subwoofer
Default Value: 0 dB
Select a value between "-15 dB" and "+12 dB". A test tone will be output each time you change the value. Select the desired level.
The speaker "Level Calibration" may be unable to be changed depending on the settings in "Configuration" - "Speaker Channels" / "Subwoofer".
"Level Calibration" cannot be changed while muting is on.
(C) Copyright 2015 Onkyo Corporation Japan. All rights reserved.
